Peli Storm Case IM3410 - Narrow and Long Gun Case
Hurry up, only 2 items left in stock.
The Peli Storm iM3410 is an IP67-rated narrow long hard case built from HPX® resin, designed to transport rifles, surveying equipment, fishing rods, and other narrow long-format items in a trim profile that minimises excess bulk. Two in-line wheels and a retractable handle with ergonomically padded grips enable rolling transport over any terrain. It is certified to MIL-STD-810F, ATA 300, and FED-STD-101C, available in No Foam or Pick 'n' Pluck Foam configurations in Black, and backed by Peli's unconditional lifetime guarantee.
Built for Gear That Is Long, Slim and Valuable
Some equipment simply does not fit a standard square case: a long gun, a surveying instrument with its extension rods, a fishing rod, a slim tool or a piece of optical gear. The iM3410 is shaped around exactly these items. With an internal length of 138.43 cm and an internal width of only 25.4 cm, it keeps long objects supported along their entire length while the outer profile stays slim enough to handle in a vehicle boot, a hallway or a crowded airport. Measure your longest item before ordering and compare it with the internal dimensions listed below.
IP67 Narrow Long-Format Protection on Wheels
The iM3410 achieves IP67 certification through a full-perimeter O-ring gasket that maintains a continuous watertight seal around the narrow lid profile. Five Press & Pull™ latches close with a positive click and distribute clamping force across the lid span, releasing with a single motion even with gloves on. Stainless steel hardware and reinforced hinges with structural ribbing resist wear and handle the torque generated by the elongated lid. Rounded, reinforced edges dissipate impact forces along the full perimeter, and the HPX® resin shell is crushproof against freight stacking, vehicle compression, and drop impacts.
Rolling Transport Without the Carry
A case this long would be tiring to carry by hand. Two in-line wheels and a retractable handle with ergonomically padded grips let you tow it over pavement, gravel and station platforms and then simply collapse the handle for storage. Stainless steel padlock hasps allow you to secure the lid when the case travels or is left in a vehicle.
Three Military and Aviation Certifications
MIL-STD-810F covers shock and vibration resistance across the conditions encountered in military logistics chains — aircraft cargo holds, ground vehicles, and field handling. FED-STD-101C validates packaging integrity under standardized pressure and environmental cycling. ATA 300 is the airline industry's specification for checked freight packaging — a case meeting ATA 300 is accepted as properly packaged under standard airline liability terms, which matters when checking long-format equipment on a commercial flight. Together, the three certifications make the iM3410 eligible for military supply chains and commercial air freight without modification.
Automatic Pressure Equalization: The Vortex™ Valve
A sealed hard case builds a pressure differential during air transport: at cruising altitude, ambient pressure is lower than the pressure sealed inside at ground level, and the differential reverses on descent. Without compensation, the lid can seal vacuum-tight by the time the case arrives, requiring significant force to open. The patented Vortex™ valve equalizes pressure automatically and continuously — no user action, no valve to open or close. This means the iM3410 opens with normal latch force after a transcontinental flight, a high-altitude drive, or a rapid shift in ambient temperature.
Where the iM3410 Earns Its Place
- Firearms transport: a long, narrow, lockable shell for rifles and other long guns. Always follow the laws and carrier rules that apply where you travel.
- Surveying and measurement: laser and optical instruments, poles and accessories stay together, protected and dry in the field.
- Outdoor and fishing: rods and other slim outdoor equipment ride safely on boats, in trucks and in the hold of a plane.
- Professional and field use: photography accessories, tools and other long items for teams that need gear to arrive in working order.
Two Configurations in Black
- No Foam — bare interior shell for customers who supply their own custom foam or plan a CNC-cut insert fitted to their exact equipment profile.
- Pick 'n' Pluck Foam — pre-scored foam divided into a grid of small cubes. Pull individual cubes with your fingers to create a custom-shaped cavity along the full interior length — no cutting tools or adhesives needed.
Available in Black only. Made in the USA and backed by Peli's unconditional lifetime guarantee.
Key Specifications
- External dimensions (L x W x H): 146.66 x 32.28 x 16.94 cm
- Internal dimensions (L x W x H): 138.43 x 25.4 x 15.24 cm
- Lid depth: 5.08 cm; base depth: 10.16 cm
- Weight empty: 8.16 kg; with foam: 9.07 kg
- Material: HPX™ resin
- Protection: IP67, MIL-STD-810F, ATA 300, FED-STD-101C
- Closure: 5 Press & Pull™ latches, stainless steel padlock hasps
- Transport: two wheels and a telescoping handle
Couldn't load pickup availability

